广东东晟油封生产厂家

怕漏油,装东晟油32余载油封研发定制生产厂家
135-8083-8085 135-8083-8085

D型不锈钢油封

产品参数

名称:D型不锈钢油封

规格:190x226x16

速度:≤18m/s

压力:≤35bar

材质:不锈钢+PTFE

应用:工程机械、液压设备

全国热线

135-8083-8085

产品介绍

不锈钢油封D型(D型不锈钢油封)双密封唇,适用压力高达35bar,PV值达100bar.m/s,也可在密封唇上添加左旋回油螺纹(BL型)或右旋回油螺纹(BR型)以提交密封性能。

东晟密封提供密封系统解决方案及产品设计服务

产品特点

构槽简单,尺寸稳定性好

THE GROOVE IS SIMPLE AND THE DIMENSION IS STABLE

D型不锈钢油封,耐高温、耐高压、耐磨无粘滞现象,在有润滑和无润滑时性能都很好。


D型不锈钢油封

不锈钢D型油封(展示图)


D型不锈钢油封

不锈钢油封D型(内唇图)





还不知道什么是不锈钢油封?赶快点击进来看看吧!它可以帮到您!

产品优势

  • 01提高生产效率INCREASE PRODUCTIVITY

    油封使其提高生产效率,深受大批量客户的认可。

  • 02油封性能优良EXCELLENT PERFORMANCE

    专注研发油封、油封修理包及油封散件,免费为客户根据需求工况设计密封方案,将其发挥密封性能,符合工作环境的需求.

应用行业

D型不锈钢油封应用行业

不锈钢油封适用于:施工工程行业、开采工程行业等.

D型不锈钢油封选型定制 - 施工工程与开采工程应用解析丨广州东晟油封厂家

D型不锈钢油封选型定制

D TYPE STAINLESS STEEL OIL SEAL SELECTION & CUSTOMIZATION


D型不锈钢油封 双密封唇与刮尘环结构实物图

不锈钢骨架+PTFE双密封唇,耐压≤35bar

STAINLESS STEEL CASE + PTFE DOUBLE SEALING LIPS, PRESSURE ≤35BAR

带刮尘环,适用于多粉尘环境

WITH DUST SCRAPER RING, SUITABLE FOR DUSTY ENVIRONMENTS

可选左旋/右旋回油螺纹(BL/BR型)

OPTIONAL LEFT/RIGHT-HAND OIL RETURN THREADS (BL/BR TYPE)

D型不锈钢油封是旋转轴用不锈钢骨架 + PTFE 双密封唇油封,在 B 型不锈钢油封基础上增加刮尘环,专为多粉尘环境设计。不锈钢外壳替代传统碳钢骨架,耐腐蚀、抗锈、尺寸稳定性好;PTFE 双密封唇耐温范围宽、耐化学腐蚀强、干摩擦系数低(约 0.04),有润滑和无润滑工况下性能均好。产品耐压 ≤35bar、线速度 ≤18m/s、PV 值达 100bar·m/s。可在密封唇上添加左旋回油螺纹(BL 型)或右旋回油螺纹(BR 型),通过轴旋转时产生的泵吸效应将泄漏油主动泵回油腔,进一步提升密封可靠性——回油螺纹方向必须与轴旋向匹配,装反会加剧泄漏。如需完整旋转密封方案,可联系广州东晟油封厂家定制。

D type stainless steel oil seal is a rotary shaft seal with stainless steel case and PTFE double sealing lips. Based on the B type stainless steel seal, it adds a dust scraper ring and is specially designed for dusty environments. The stainless steel outer case replaces the traditional carbon steel skeleton, offering corrosion resistance, rust resistance and good dimensional stability. The PTFE double sealing lips provide a wide temperature range, strong chemical resistance and a low dry friction coefficient (~0.04), performing well in both lubricated and non-lubricated conditions. The product withstands pressure up to 35bar, linear speed up to 18m/s, with a PV value of 100bar·m/s. Optional left-hand oil return threads (BL type) or right-hand oil return threads (BR type) can be added to the sealing lip — the pumping effect generated during shaft rotation actively pumps leaked oil back into the oil chamber, further improving sealing reliability. The thread direction must match the shaft rotation direction; installing it reversed will aggravate leakage.

施工工程 Construction Engineering

图片中装载机与摊铺机协同进行路面摊铺作业的场景,正是 D 型不锈钢油封的核心应用场合之一。施工工程中,旋转轴类部件广泛分布在装载机/挖掘机的行走减速机、回转减速机、液压泵驱动轴、发动机曲轴前后端,摊铺机的螺旋分料器驱动轴、熨平板振动轴,压路机的振动轮偏心轴等部位。这些旋转轴共同面对三重挑战:沥青/混凝土粉尘(莫氏硬度 4~5)持续侵袭、雨水与泥浆交替浸泡、户外露天存放导致的骨架锈蚀。传统碳钢骨架 TC 油封在这种环境下,骨架锈蚀后会产生锈蚀颗粒脱落污染密封唇口,造成二次磨损;而普通不带刮尘环的油封,粉尘会沿轴面逐渐爬入唇口下方形成磨粒磨损。D型不锈钢油封的不锈钢骨架从根本上解决锈蚀问题——不锈钢在户外潮湿、酸雨、泥浆环境下不生锈,骨架尺寸长期稳定;PTFE 双密封唇主唇封油、副唇封尘,配合外置刮尘环形成三道防线,粉尘在接触主唇前即被刮除。对于摊铺机螺旋分料器驱动轴这类高温(沥青温度 150~180℃ 辐射)+ 粉尘(沥青焦粒)+ 低速重载的工况,PTFE 的耐高温特性远优于 NBR 橡胶唇口,不会因热老化而硬化开裂。选型时需注意:摊铺机螺旋轴通常单向连续旋转,可选用 BL/BR 回油螺纹型进一步提升密封性;而行走减速机、回转减速机等正反转频繁的轴,不宜使用回油螺纹型——反转时回油螺纹会反向泵油,将外部污染物泵入油腔。轴面粗糙度要求 Ra 0.2~0.8μm(高速轴 0.2~0.4μm),轴面硬度 ≥HRC45,严禁螺旋加工纹(会与回油螺纹叠加产生异常泵油效应)。如需针对特定施工设备的旋转密封方案,可联系广州东晟油封厂家定制。

The scene of a loader and a paver working together on road paving shown in the image is one of the core application scenarios for D type stainless steel oil seals. In construction engineering, rotary shaft components are widely distributed in travel reducers, swing reducers, hydraulic pump drive shafts and engine crankshaft front/rear ends of loaders/excavators; screw feeder drive shafts and screed vibration shafts of pavers; and eccentric shafts of vibratory drums on rollers. These rotary shafts face three common challenges: continuous invasion of asphalt/concrete dust (Mohs hardness 4~5), alternating immersion in rain and mud, and skeleton rusting caused by outdoor storage. With traditional carbon steel TC seals, the rusted skeleton sheds rust particles that contaminate the sealing lip, causing secondary wear; seals without a scraper ring allow dust to gradually creep under the lip along the shaft surface, causing abrasive wear. The stainless steel case of the D type stainless steel oil seal fundamentally solves the rust problem — stainless steel does not rust in outdoor humidity, acid rain or mud, and the case dimensions remain stable over time. The PTFE double sealing lips feature a main lip for oil sealing and a secondary lip for dust sealing, combined with an external scraper ring to form a three-line defense that removes dust before it contacts the main lip. For conditions such as paver screw feeder drive shafts with high temperature (asphalt radiation at 150~180℃), dust (asphalt coke particles) and low-speed heavy loads, PTFE's high-temperature resistance far exceeds that of NBR rubber lips and will not harden or crack from thermal aging. Selection notes: paver screw shafts usually rotate continuously in one direction, so BL/BR oil return thread types can be selected to further improve sealing; however, shafts with frequent forward/reverse rotation such as travel reducers and swing reducers should not use oil return thread types — reverse rotation causes the thread to pump oil backward, drawing external contaminants into the oil chamber. Shaft surface roughness should be Ra 0.2~0.8μm (0.2~0.4μm for high-speed shafts), shaft hardness ≥HRC45, and spiral machining marks are strictly prohibited (they would superimpose with the oil return thread to produce abnormal pumping effects).

开采工程 Mining Engineering

图片中大型矿用挖掘机(如小松 PC4000 级)在露天矿场进行装载作业的场景,展示了开采工程对旋转密封的极端要求。开采工程中的旋转轴分布在矿用挖掘机/装载机的行走减速机、回转减速机、液压泵驱动轴,矿用自卸车的轮边减速器、电动轮端部,牙轮钻机的钻杆旋转接头,破碎机的偏心轴与轴承座等关键部位。这些部位的共同特征是大轴径、重载荷、高磨粒浓度——矿用设备轴径通常在 100~400mm,岩石碎屑(花岗岩/玄武岩莫氏硬度 6~7)与铁矿/石英粉持续侵袭,轴面一旦被磨粒犁出沟痕,任何油封都会快速失效。开采工程对 D 型不锈钢油封的需求集中在两个维度:一是抗磨粒侵入能力——不锈钢骨架刚性好、不变形,PTFE 双唇 + 刮尘环的三重防护确保即使在高浓度石英砂粉尘环境中,主密封唇仍能得到有效保护;PTFE 材质的磨粒嵌入特性(软质 PTFE 允许部分硬颗粒嵌入表层而非犁削穿透)进一步延长了唇口寿命。二是耐腐蚀能力——矿山环境中酸性矿水(pH 可低至 3~4)、含硫地下水、选矿药剂残留对碳钢骨架腐蚀性极强,不锈钢骨架在此环境中具有不可替代的优势。D型不锈钢油封的≤35bar 耐压能力覆盖了绝大多数矿山减速机与泵轴的密封压力需求(减速机内部齿轮油通常无压或微压,但矿山设备重载冲击下会产生瞬时压力脉动);≤18m/s 的线速度覆盖了液压泵驱动轴的高速旋转需求。矿用自卸车轮边减速器等低速重载、粉尘极重的部位,建议选用带刮尘环的 D 型并配合浮动油封组成双重防护——浮动油封承担主要粉尘阻挡与重载密封,D 型不锈钢油封作为第二道防线。选型时需提供轴径 + 座孔 + 转速 + 旋向(单向/双向)+ 介质(齿轮油/液压油)+ 环境温度 + 粉尘浓度,特别是矿山水质的酸碱性——强酸性环境需确认不锈钢牌号(304 或 316L)是否满足耐腐蚀要求。如需矿山设备旋转密封整体方案,可联系广州东晟油封厂家定制。

The scene of a large mining excavator (such as a Komatsu PC4000 class) performing loading operations at an open-pit mine shown in the image demonstrates the extreme requirements of mining engineering for rotary seals. In mining engineering, rotary shafts are located at travel reducers, swing reducers and hydraulic pump drive shafts of mining excavators/loaders; wheel-side reducers and electric wheel ends of mining dump trucks; drill rod rotary joints of rotary drills; and eccentric shafts and bearing housings of crushers. These positions share the characteristics of large shaft diameters, heavy loads and high abrasive concentration — mining equipment shaft diameters typically range from 100~400mm, with continuous invasion by rock debris (granite/basalt Mohs hardness 6~7) and iron ore/quartz powder. Once the shaft surface is grooved by abrasives, any oil seal will fail rapidly. The demand for D type stainless steel oil seals in mining engineering focuses on two dimensions: first, abrasive intrusion resistance — the stainless steel case has good rigidity and does not deform; the triple protection of PTFE double lips + scraper ring ensures the main sealing lip is effectively protected even in high-concentration quartz sand dust; PTFE's abrasive embedding property (soft PTFE allows some hard particles to embed into the surface layer rather than ploughing through) further extends lip life. Second, corrosion resistance — in mining environments, acidic mine water (pH as low as 3~4), sulfur-bearing groundwater and beneficiation reagent residues are extremely corrosive to carbon steel cases, giving stainless steel cases an irreplaceable advantage. The ≤35bar pressure resistance of the D type stainless steel oil seal covers the sealing pressure requirements of most mining reducers and pump shafts (gear oil inside reducers is usually unpressurized or slightly pressurized, but heavy-load impacts on mining equipment generate transient pressure pulsations); the ≤18m/s linear speed covers the high-speed rotation requirements of hydraulic pump drive shafts. For positions with extremely heavy dust and low-speed heavy loads such as mining dump truck wheel-side reducers, it is recommended to use the D type with scraper ring in combination with a floating oil seal for dual protection — the floating seal bears the main dust blocking and heavy-load sealing, while the D type stainless steel oil seal serves as the second line of defense. Selection should specify shaft diameter, housing bore, rotation speed, rotation direction (unidirectional/bidirectional), media (gear oil/hydraulic oil), ambient temperature and dust concentration, especially the acidity/alkalinity of mine water — strongly acidic environments require confirmation of whether the stainless steel grade (304 or 316L) meets corrosion resistance requirements.

压力≤35bar,速度≤18m/s,PV值100bar·m/s

PRESSURE ≤35BAR, SPEED ≤18M/S, PV VALUE 100BAR·M/S

结构形式:不锈钢骨架 + PTFE 双密封唇 + 外置刮尘环(B 型基础上增加刮尘环),旋转轴用
材质:不锈钢外壳(304/316L 可选)+ PTFE 密封唇
压力范围:≤35bar(3.5MPa),适用于减速机、泵轴等旋转密封压力
线速度:≤18m/s(高速轴需确认轴面粗糙度 Ra 0.2~0.4μm)
PV 值:100bar·m/s(压力×速度的乘积上限,选型时需同时校核压力与速度)
回油螺纹:可选 BL 型(左旋)/ BR 型(右旋),仅适用于单向旋转轴,旋向必须与螺纹方向匹配,装反会加剧泄漏;正反转轴禁用
轴面要求:Ra 0.2~0.8μm(高速轴 0.2~0.4μm),硬度 ≥HRC45,严禁螺旋加工纹(与回油螺纹叠加产生异常泵油)
安装方向:主密封唇朝向油腔侧,刮尘环朝向外部粉尘侧,装反会导致油液泄漏且粉尘直接进入
适配介质:矿物齿轮油、液压油、润滑脂;PTFE 不耐熔融碱金属、元素氟、部分卤化烃
非标定制:可按轴径、座孔、宽度、转速、介质定制,访问广州东晟油封厂家官网获取支持

D型不锈钢油封适用设备:装载机 Wheel Loader、摊铺机 Paver、压路机 Road Roller、矿用挖掘机 Mining Excavator、矿用自卸车 Mining Dump Truck、牙轮钻机 Rotary Drill、行走减速机 Travel Reducer、回转减速机 Swing Reducer、液压泵 Hydraulic Pump、螺旋分料器 Screw Feeder

Application Scenarios for D Type Stainless Steel Oil Seals: Wheel Loader, Paver, Road Roller, Mining Excavator, Mining Dump Truck, Rotary Drill, Travel Reducer, Swing Reducer, Hydraulic Pump, Screw Feeder

施工工程 & 开采工程 油封完整清单

① 施工工程 Construction Engineering(装载机/摊铺机/压路机/挖掘机/推土机/平地机/混凝土泵车)
       ├─ D型不锈钢油封(不锈钢骨架+PTFE双唇+刮尘环,旋转轴,行走/回转减速机、泵轴、摊铺机螺旋轴,≤35bar/≤18m/s)
       ├─ B型不锈钢油封(不锈钢骨架+PTFE唇,无刮尘环,粉尘较少工况)
       ├─ D型不锈钢油封 BL/BR 回油螺纹型(单向旋转轴专用,如摊铺机螺旋分料器轴)
       ├─ TC 双唇骨架油封(碳钢骨架+NBR唇,通用旋转轴,行走/回转减速机)
       ├─ TC/FKM 氟橡胶骨架油封(摊铺机熨平板高温部位、发动机曲轴)
       ├─ TB 外骨架油封(外露铁壳,座孔密封)
       ├─ TA 单唇骨架油封(低压旋转轴)
       ├─ DSJP破碎锤油封(PTFE+铜粉/NBR,破碎锤打击活塞往复密封,≤60MPa)
       ├─ SPGW 组合油封(孔用,挖掘机液压缸活塞,PTFE+O型圈+挡圈,≤50MPa)
       ├─ 格莱圈 Gland Seal(孔用,液压缸活塞高压双向密封)
       ├─ 斯特封 Step Seal(杆用,液压缸活塞杆高压密封)
       ├─ Y 型 NBR 油封(通用往复液压缸)
       ├─ Y 型 FKM 氟橡胶油封(摊铺机高温液压缸)
       ├─ V 型夹布油封(混凝土泵车主液压缸高压活塞)
       ├─ DSZ 铁壳防尘圈(液压缸导向套前端,挡沥青/混凝土碎粒)
       ├─ DKBI 铁壳+PU 防尘圈(二级防尘,抗硬颗粒)
       ├─ C 型全 PTFE 油封(沥青/混凝土粉尘+化学腐蚀工况)
       ├─ PTFE 组合密封(PTFE 滑环+O 型圈,低摩擦往复)
       ├─ 导向环 / 支撑环(POM/PTFE 复合材料,活塞导向)
       ├─ 缓冲圈(抗冲击峰值压力)
       ├─ 浮动油封(履带行走机构驱动轮端,重载防尘)
       ├─ 旋转接头油封(中心回转体多通道液压)
       ├─ O 型圈(GB/T 3452.1,NBR/FKM/EPDM,系统各部位)
       ├─ O 型圈挡圈(POM/PTFE,高压防挤出)
       ├─ 机械密封(水泵/马达轴端)
       └─ 油封修理包(挖掘机/装载机/摊铺机全机配套)

② 开采工程 Mining Engineering(矿用挖掘机/矿用自卸车/牙轮钻机/破碎机/地下铲运机)
       ├─ D型不锈钢油封(不锈钢骨架+PTFE双唇+刮尘环,矿用挖掘机行走/回转减速机、自卸车轮边减速器,≤35bar/≤18m/s)
       ├─ D型不锈钢油封 316L 材质型(强酸性矿水环境,耐腐蚀升级)
       ├─ B型不锈钢油封(不锈钢骨架+PTFE唇,粉尘较少工况)
       ├─ TC/FKM 氟橡胶骨架油封(耐矿水腐蚀旋转轴)
       ├─ TC 双唇骨架油封(通用旋转轴,减速机/泵轴)
       ├─ 浮动油封(矿用自卸车轮边/履带驱动轮,重载防尘第一道防线,与 D 型组成双重防护)
       ├─ DSJP破碎锤油封(PTFE+铜粉/NBR,矿用破碎锤打击活塞,抗花岗岩/玄武岩磨粒,≤60MPa)
       ├─ SPGW 组合油封(孔用,矿用挖掘机液压缸活塞,高压无粘滞,≤50MPa)
       ├─ 格莱圈 Gland Seal(孔用,大臂/斗杆/铲斗液压缸活塞)
       ├─ 斯特封 Step Seal(杆用,高压活塞杆端)
       ├─ Y 型 NBR 油封(通用往复)
       ├─ Y 型 FKM 氟橡胶油封(酸性矿水/高温辐射工况)
       ├─ V 型氟橡胶夹布油封(超高压重载活塞)
       ├─ DSZ 铁壳防尘圈(液压缸导向套前端,挡岩石碎粒)
       ├─ DKBI 铁壳+PU 二级防尘圈(矿山硬颗粒,比 DSZ 单唇更强)
       ├─ C 型全 PTFE 油封(石英砂/铁矿石粉磨粒+酸性矿水双重腐蚀)
       ├─ PTFE 组合密封(PTFE 滑环+FKM O 型圈,高温高压)
       ├─ 导向环(高耐磨 PTFE 复合材料,抗矿石磨粒犁削)
       ├─ POM 支撑环(重载大缸径,抗挤压)
       ├─ 缓冲圈(抗爆破冲击载荷)
       ├─ 旋转接头油封(牙轮钻机钻杆旋转接头、中心回转体多通道)
       ├─ 机械密封(矿用水泵/冷却泵轴端)
       ├─ O 型圈(FKM 为主,NBR 常温部位)
       ├─ O 型圈挡圈(POM/PTFE,高压防挤出)
       └─ 全缸密封修理包(矿用挖掘机/自卸车/钻机原厂配套)

以上清单仅为主要工况,完整选型请告知轴径 + 座孔 + 转速 + 旋向(单向/双向)+ 介质 + 温度 + 粉尘浓度 + 水质酸碱性,联系广州东晟油封厂家定制旋转密封整体方案。

广州东晟油封厂家

GUANGZHOU DONGSHENG OIL SEAL MANUFACTURER

dshseals.cn

集研发、生产、销售于一体的国家高新技术油封厂家 · 235种材料配方 · 1725种选型方案

National High-Tech Enterprise integrating R&D, Production and Sales · 235 Material Formulations · 1725 Selection Solutions


使用说明

与B型油封相同,但增加刮尘环,可应用于多粉尘环境

D型不锈钢油封 使用说明 - 广州东晟油封厂家

D型不锈钢油封 使用说明

D-TYPE STAINLESS STEEL OIL SEAL · INSTALLATION & MAINTENANCE GUIDE

D型不锈钢油封 双密封唇与刮尘环结构实物图

D型不锈钢油封实物图 · 不锈钢骨架 + PTFE 双唇 + 刮尘环

结构与材质 Structure & Material

D型不锈钢油封属于旋转轴唇形密封圈,结构与 B 型油封相同,区别在于D型不锈钢油封在唇部增加了刮尘环,因此可直接用于多粉尘环境。D型不锈钢油封采用双密封唇:一道主唇封油、一道副唇挡尘,外部再叠加刮尘环形成"挡尘—挡尘—封油"的三级防护顺序,这也是D型不锈钢油封比普通骨架油封更适合粉尘工况的核心原因。材质方面,D型不锈钢油封由不锈钢骨架 + PTFE 唇口组成,不锈钢骨架抗腐蚀、压装后不变形,PTFE 唇口耐高温、耐高压、耐磨且无粘滞,在有润滑与无润滑条件下性能都稳定。D型不锈钢油封常用规格为 190×226×16,适用压力 ≤35bar,线速度 ≤18m/s,PV 值达 100 bar·m/s;还可在 D型不锈钢油封 的密封唇上加工左旋回油螺纹(BL型)或右旋回油螺纹(BR型),利用旋转泵吸把渗到唇口的油推回油腔。需要完整规格与图纸,可查看D型不锈钢油封产品页,或联系广州东晟油封厂家定制。

D-type stainless steel oil seal is a rotary shaft lip seal whose structure follows the B-type design, except that a dust scraper ring is added at the lip, making it directly usable in dusty environments. It has double sealing lips — one main lip retaining oil, one secondary lip blocking dust — with the scraper ring adding a third barrier, giving the sequence "dust blocking — dust blocking — oil retention", which is why the D-type seal suits dusty conditions better than an ordinary skeleton seal. Material-wise it combines a stainless steel skeleton with a PTFE lip: the stainless skeleton resists corrosion and does not deform after press-in, while the PTFE lip offers high temperature and pressure resistance, wear resistance and no stick-slip, performing stably with or without lubrication. Standard size is 190×226×16, rated pressure ≤35 bar, linear speed ≤18 m/s and PV value up to 100 bar·m/s. The lip can be machined with left-hand (BL) or right-hand (BR) oil return threads so the pumping effect of rotation pushes seeped oil back into the sump.

安装要点 Installation Key Points

① 安装方向:D型不锈钢油封的主唇必须朝向油腔侧,刮尘环朝向外部粉尘侧,两侧不可对调。装反以后刮尘环会刮掉轴面油膜,D型不锈钢油封的主唇随即在干摩擦下加速磨损,这种情况下装反比不装更糟。
② 轴面要求:轴颈硬度 ≥HRC45,表面粗糙度 Ra 0.2~0.4μm,严禁螺旋加工纹(会形成泵油效应把油往外推),也不允许锈蚀、毛刺与磕碰。D型不锈钢油封的 PTFE 唇口对轴面状态比橡胶唇更敏感,轴面不达标时D型不锈钢油封的寿命会明显缩短。
③ 座孔要求:座孔按D型不锈钢油封的规格表加工,孔径公差、同轴度与端面垂直度都需达标;孔口倒角 15°~30° 并去净毛刺与切屑,压装前用洁净布擦净孔壁油污与铁屑。
④ 压装方法:在D型不锈钢油封的唇口与骨架外圆涂抹清洁液压油或锂基脂,使用专用压套垂直于座孔均匀压入,严禁锤击、斜压或用撬杠——不锈钢骨架虽不易锈,但压偏会让D型不锈钢油封整体倾斜,导致单侧偏磨。油封厂家可配套提供专用压装工装。
⑤ 轴穿过唇口:轴端必须倒圆或加导向套,花键、键槽、螺纹处应套上保护套再穿过D型不锈钢油封,否则锐边会切伤唇口;PTFE 唇口一旦被划伤无法修复,只能整套更换。
⑥ 润滑与跑合:装配完成后向油腔注入规定油量,先低速空载运转 10~15 分钟让D型不锈钢油封的唇口完成初始跑合,再逐步加载;跑合期内出现轻微渗油属正常现象,D型不锈钢油封的唇口贴合稳定后会自行收敛。

① Direction: The main lip of the D-type stainless steel oil seal must face the oil chamber while the scraper ring faces the external dust side — never swap them. Reversed installation makes the scraper ring wipe the shaft oil film away, after which the main lip runs dry and wears rapidly; reversed is worse than not installed at all.
② Shaft Surface: Shaft hardness ≥HRC45, roughness Ra 0.2~0.4μm, no helical machining marks (they create a pumping effect pushing oil outward), and no rust, burrs or dents. The PTFE lip is more sensitive to shaft condition than a rubber lip, and poor shaft finish noticeably shortens service life.
③ Housing Bore: Machine the bore per the dimension table — diameter tolerance, concentricity and face squareness must all be within limits. Chamfer the bore entry 15°~30°, remove burrs and chips, and wipe the bore clean before press-in.
④ Press-in: Apply clean hydraulic oil or lithium grease to the lip and the skeleton outer diameter, then press in perpendicularly with a dedicated sleeve and even force. Never hammer, press at an angle or pry — a skewed press tilts the whole seal and causes one-sided wear.
⑤ Shaft Insertion: Round the shaft end or use a guide sleeve; cover splines, keyways and threads with a protective sleeve before passing them through the seal, otherwise sharp edges cut the lip, which cannot be repaired.
⑥ Lubrication & Running-in: Fill the specified oil quantity and run at low speed and no load for 10~15 minutes so the lip seats, then increase load gradually. Slight seepage during running-in is normal and settles once the lip conforms.

D型不锈钢油封 结构与细节实拍

D型不锈钢油封 内唇与刮尘环细节

安装前请对照实物确认D型不锈钢油封的主唇朝向与刮尘环位置

工况参数 Operating Parameters

常用规格:D型不锈钢油封 190×226×16(d×D×H),可按轴径、座孔与厚度非标定制
结构形式:D型不锈钢油封为双密封唇 + 刮尘环,可选 BL 左旋 / BR 右旋回油螺纹
材质:D型不锈钢油封采用不锈钢骨架 + PTFE 唇口
压力范围:D型不锈钢油封 ≤35bar(约 3.5MPa),超压工况必须改用耐压更高的组合密封,不可超压使用
速度范围:D型不锈钢油封 ≤18m/s
PV 值:D型不锈钢油封可达 100 bar·m/s,压力与线速度的乘积超过该值后摩擦热骤增
温度范围:PTFE 唇口本身耐温较宽,实际允许温度以轴温与油温的较低值为准;持续高温工况应与厂家确认D型不锈钢油封的具体温度等级
适用介质:矿物油、齿轮油、液压油、润滑脂;PTFE 不耐熔融碱金属、元素氟与部分卤化烃
不适配工况:干摩擦高速、强磨粒浆料浸泡、轴端背压超过 35bar 的部位,均不建议直接使用D型不锈钢油封
选型提示:D型不锈钢油封与 B 型油封尺寸体系一致,可直接替换清洁工况下的 B 型件以提升抗粉尘能力
备件管理:建议常备一件同规格D型不锈钢油封,粉尘工况下D型不锈钢油封属于易损件;存放时D型不锈钢油封应避光平放、远离热源,不得悬挂或重压,以免D型不锈钢油封的唇口变形;开封后检查D型不锈钢油封的刃口是否完整再安装

Standard Size: 190×226×16 (d×D×H); non-standard shaft, bore and thickness available to order.
Structure: Double sealing lips plus a dust scraper ring, with optional BL left-hand or BR right-hand oil return threads.
Material: Stainless steel skeleton with PTFE lip.
Pressure: ≤35 bar (about 3.5MPa) — higher back pressure requires a higher-pressure combination seal; do not exceed the rating.
Speed: ≤18 m/s.
PV Value: Up to 100 bar·m/s; beyond this the product of pressure and speed causes rapid frictional heating.
Temperature: The PTFE lip tolerates a wide range; the actual limit follows the lower of shaft and oil temperature — confirm the specific temperature class with the manufacturer for continuous high-temperature duty.
Media: Mineral oil, gear oil, hydraulic oil and grease; PTFE is not resistant to molten alkali metals, elemental fluorine or some halogenated hydrocarbons.
Not Recommended: High-speed dry running, immersion in heavily abrasive slurry, or shaft-end back pressure above 35 bar.
Selection Note: Dimensions match the B-type series, so the D-type seal can directly replace a B-type seal in clean duty to gain dust resistance.

维护周期 & 失效排查 Maintenance & Failure Diagnosis

维护周期:
· 清洁工况(室内设备、油温稳定、粉尘少):D型不锈钢油封建议 8000~12000 小时或每年检查一次
· 多粉尘工况(施工、开采、拌合、破碎筛分):D型不锈钢油封建议 3000~5000 小时或每季度检查一次,重点看刮尘环
· 检查内容:D型不锈钢油封的唇口磨损带宽度、刮尘环是否缺口或翻卷、骨架外圆是否有松动锈迹、轴面是否有沟痕、轴端是否有渗油积灰

常见失效与排查:
· 刮尘环缺口或翻卷 → 粉尘颗粒犁削或装配时被锐边刮伤,D型不锈钢油封须整套更换,同时检查轴端倒角与保护套使用是否规范
· 唇口磨损带过宽、渗油 → 轴面粗糙度超标或存在螺旋加工纹,抛光轴面至 Ra 0.2~0.4μm 后更换D型不锈钢油封
· 唇口偏磨、单侧发亮 → 座孔与轴同轴度超差或压装倾斜,重新校核同轴度并垂直压入新的D型不锈钢油封
· PTFE 唇口发黑、边缘熔融 → 超速或超压导致摩擦热过高,核对转速与压力是否在D型不锈钢油封的 18m/s、35bar 限值内
· 外圈渗油并积灰成泥 → 回油能力不足或腔体内压偏高,改用 BL/BR 回油螺纹版本的D型不锈钢油封,并检查通气孔是否堵塞
· 骨架外圆松动、密封整体位移 → 座孔尺寸超差或装配过盈不足,修复座孔后重新压装D型不锈钢油封,必要时改用带外密封胶的结构

更换判定:当D型不锈钢油封的磨损带宽度超过唇口厚度一半时即应更换;现场若无法精密测量,可用新旧件对比的方式判断D型不锈钢油封是否需要换新。同一工位两侧对称布置时,建议同步更换另一侧的D型不锈钢油封,避免新旧密封混用造成偏载与二次返工。

Maintenance Intervals:
· Clean Duty (indoor equipment, stable oil temperature, little dust): inspect every 8000~12000 hours or annually.
· Dusty Duty (construction, mining, mixing, crushing and screening): inspect every 3000~5000 hours or quarterly, focusing on the scraper ring.
· Inspection Items: Lip wear band width, scraper ring notching or curling, looseness or rust at the skeleton outer diameter, shaft grooving, oil seepage with dust caking.

Common Failures & Diagnosis:
· Scraper Ring Notched or Curled → Abrasive ploughing or damage by sharp edges during assembly. Replace the whole seal and verify shaft chamfer and protective sleeve usage.
· Wide Wear Band with Seepage → Shaft roughness out of specification or helical machining marks present. Polish the shaft to Ra 0.2~0.4μm and replace the seal.
· One-Sided, Bright Wear → Concentricity error between bore and shaft, or skewed press-in. Re-check concentricity and press the new seal in perpendicularly.
· PTFE Lip Blackened or Melted at the Edge → Frictional overheating from overspeed or overpressure. Verify speed and pressure are within the 18 m/s and 35 bar limits.
· Outer Ring Seeping and Caking with Dust → Insufficient oil return or excessive housing pressure. Switch to the BL/BR return-thread version and check that the breather is not blocked.
· Loose Skeleton, Whole Seal Displaced → Bore dimension out of tolerance or insufficient interference. Repair the bore, re-press the seal, and consider a structure with external sealant.

D型不锈钢油封适用设备:工程机械 Construction Machinery、液压设备 Hydraulic Equipment、轮式装载机 Wheel Loader、沥青摊铺机 Asphalt Paver、压路机 Roller、混凝土泵车 Concrete Pump Truck、旋挖钻机 Rotary Drilling Rig、矿用挖掘机 Mining Excavator、球磨机 Ball Mill、渣浆泵 Slurry Pump、皮带机滚筒 Conveyor Pulley、振动筛 Vibrating Screen

上述设备中,D型不锈钢油封主要装在减速机输出轴、马达轴端与滚筒轴端等旋转部位;粉尘含量高的工位可再前置一道防尘圈,与D型不锈钢油封形成二级防护。若需要成套密封方案或非标尺寸,可联系广州东晟油封厂家,说明轴径 d / 座孔 D / 厚度 H + 转速 + 压力 + 温度 + 粉尘浓度七项参数即可选型。日常保养时,D型不锈钢油封的检查应结合设备停机窗口安排,不必等到渗油再拆;D型不锈钢油封与 B 型油封尺寸一致、现场可互换,但D型不锈钢油封的刮尘环位置必须朝外,备件混放时最容易装错,建议在D型不锈钢油封的包装上直接标注朝向。旧件拆下后应留存比对磨损带,据此判断D型不锈钢油封的失效原因——偏磨指向同轴度,均匀磨薄指向轴面粗糙度或粉尘侵入。

广州东晟油封厂家

GUANGZHOU DONGSHENG OIL SEAL MANUFACTURER

dshseals.cn

集研发、生产、销售于一体的国家高新技术油封厂家 · 235种材料配方 · 1725种选型方案

National High-Tech Enterprise integrating R&D, Production and Sales · 235 Material Formulations · 1725 Selection Solutions


联系我们

尊敬的访客

东晟密封主要从事各种行业油封、油封修理包、工程机械油封散件的研究、制造和销售。产品广泛用于:工程机械、航天、石油、化工、冶金、电力、汽车、造船、煤矿、电子、家电、卫浴、泵阀、造纸、液压、气动、机器人、无人机、盾构机、智能制造等行业。

全国咨询热线:400-0087-996

  • 联系手机联系手机13580830786
  • 联系邮箱联系邮箱3030651527@qq.com
  • 公司地址公司地址广东省东莞市石碣镇横滘工业区伟业街4号

寻找适合您应用的油封?东晟为您设计严苛条件下运行的油封,免费提供全方位油封系统解决方案!

产品定制咨询

热品推荐 / Hot product

A型PTFE油封

A型PTFE油封是由PTFE+碳纤材质制作而成,具有很好的耐磨耐高温以及耐水性.

B1型全PTFE油封

B1型全PTFE油封是一款新结构类型的PTFE油封产品,由PTFE和碳纤材料制作...

四氟H型油封

安装广州聚四氟乙烯H型油封时,必须将安装部位的锈渍、脏物、毛刺等清除干净;要保护...

聚四氟乙烯B型油封

聚四氟乙烯B型油封,这是款材质采取广州全PTFE的系列B型油封产品,全铁氟龙双密...

产品中心

咨询热线

135-8083-8085